Dodge Ram Dead Battery Reset

Dodge Ram trucks are known for their durability and power. But even the most reliable truck can have problems, like a dead battery. If your Ram’s battery dies, don’t panic.

There is a simple way to reset it.

If your Dodge Ram has a dead battery, you can reset it using the following steps: 1. Open the hood and locate the battery. 2. Disconnect the negative terminal from the battery.

3. Touch the positive terminal to the negative terminal for 30 seconds. 4. Reconnect the negative terminal to the battery. 5. Close the hood and start your Dodge Ram.

Dodge Ram Dead Battery Reset


How Do You Reset the Battery on a Dodge Ram 1500?

If your Dodge Ram 1500 is having battery issues, you may need to reset the battery. To do this, you’ll need to disconnect the negative terminal from the battery and then reconnect it after about 30 seconds. This will help to break any corrosion that has built up on the terminals and should help to reset the battery.

How Do I Reset My Ram 1500 After Replacing the Battery?

If you’ve recently replaced the battery in your RAM 1500, you may be wondering how to reset the truck’s computer. Here’s a quick guide on how to do just that: 1. Disconnect the negative battery cable from the truck’s battery.

2. Touch the positive and negative battery cables together for 30 seconds. This will discharge any residual power in the system and help reset the computer. 3. Reconnect the negative battery cable to the truck’s battery.

4. Start the truck and let it idle for about 5 minutes so that the computer can relearn its idle settings. 5. Take the truck for a short drive (about 10 minutes) so that it can relearn its fuel-injection and ignition timing settings.

How Do I Get My Dodge Ram Out of Theft Mode?

If your Dodge Ram has been placed into theft mode, there are a few things you can do to get it out. First, try using the key fob to unlock the doors. If that doesn’t work, you can try disconnecting and reconnecting the battery.

Finally, if all else fails, you can contact a dealer or locksmith to have them disable the theft mode for you.

What is Dodge Ram Battery Saver Mode?

Dodge Ram battery saver mode is a setting that can be activated when the vehicle is not in use. This feature helps to preserve the life of the battery by shutting off power-hungry features and accessories. When properly used, battery saver mode can extend the amount of time between charges and help to keep your Dodge Ram running like new.

How To Find A Battery Drain My RAM Truck Always Has A Dead Battery!

Dodge Ram Won’T Idle After Dead Battery

If your Dodge Ram won’t idle after you’ve had a dead battery, there are a few things you can try to get it going again. First, check the battery terminals to make sure they’re clean and free of corrosion. Next, check the alternator belt to see if it’s loose or needs to be replaced.

Finally, check the engine oil level and add more oil if necessary. If none of these solutions work, then you may need to take your Ram to a mechanic for further diagnosis.

2015 Dodge Ram Radio Reset

If you’re like most people, your car is one of your biggest investments. And keeping it running like new is important to you. That’s why when something goes wrong, it’s important to know how to fix it yourself.

One common issue that arises with car radios is the need for a reset. Whether it’s because of a power outage or simply because the radio was turned off for too long, a reset may be necessary to get your radio working again. Here’s how to do a 2015 Dodge Ram radio reset:

1. Press and hold the “Tune” button on the steering wheel for about five seconds. This should bring up a message on the screen that says “Entering Setup Mode.” 2. Use the arrow buttons on the steering wheel to scroll through the menu options until you see “Reset.”

Select this option by pressing the “OK” button in the center of the steering wheel. 3. You’ll be prompted to confirm whether or not you want to reset the radio. Choose “Yes” and then press “OK.”

The radio will take a minute or so to restart and then should be working properly again!

Ram 1500 Battery Drain

The Ram 1500 is a great truck, but like any vehicle, it can have its problems. One issue that some owners have reported is a battery drain. This can be caused by a number of things, so it’s important to diagnose the problem correctly in order to fix it.

One possible cause of battery drain is a faulty alternator. If the alternator isn’t charging the battery properly, then the battery will eventually run out of power and die. Another possibility is that there is a parasitic draw on the electrical system.

This means that something is drawing power from the battery even when the truck is turned off. The best way to diagnose these problems is with a voltmeter. You can check the voltage at the battery while the engine is running and compare it to what it should be (around 14 volts).

If you’re seeing a lower voltage, then that’s an indication that there may be an issue with the alternator or another component in the charging system. If you see a higher voltage, then there may be a parasitic draw on the system. Once you’ve diagnosed the problem, you can take steps to fix it.

If it’s simply a matter of replacing worn out parts like belts or pulleys, then that’s relatively easy to do yourself (or have done at a shop). However, if there’s more serious damage like burnt out bearings in the alternator, then you’ll need to replace that component entirely which can be quite expensive. Regardless of what needs to be done, fixing this problem will keep your Ram 1500 running smoothly for years to come!

How to Change Battery in Ram 1500

If you’re like most people, you probably don’t think about your car’s battery until it’s time to change it. But if you’re the owner of a Ram 1500 truck, it’s important to know how to change the battery so you can keep your truck running smoothly. Here’s a step-by-step guide to changing the battery in your Ram 1500:

1. Open the hood and locate the battery. The battery is usually located near the front of the engine compartment on the driver’s side. 2. Disconnect the negative (black) cable from the terminal first, and then disconnect the positive (red) cable.

Be sure not to touch any metal surfaces with your bare hands while doing this, as static electricity can damage electronic components. 3. Remove the old battery from its tray and dispose of it properly. Many auto parts stores will take used batteries for recycling.

4. Install the new battery in its tray and reconnect both cables, making sure that they are tight against their respective terminals.


If you have a Dodge Ram with a dead battery, there are a few ways you can reset it. First, try disconnecting the negative battery cable for about five minutes. If that doesn’t work, then you can try jump starting the vehicle.

Finally, if those two methods don’t work, then you’ll need to replace the battery.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *