Ford F150 Parking Brake Cable Replacement

The Ford F150 Parking Brake Cable Replacement process is relatively simple. Begin by parking the vehicle on a level surface and setting the parking brake. Disconnect the negative battery cable to ensure safety while working with electrical components.

Next, remove the center console and disconnect any necessary wiring harnesses that are in the way of accessing the emergency brakes system. Then, unbolt and detach both ends of each cables from their mounting points before moving forward with removing them from within their clips or bushings along the frame rail. Finally, install new cables in reverse order ensuring they are properly secured at both ends before reconnecting all electrical wiring previously disconnected as well as re-installing your center console for a complete repair job!

If you need to replace the parking brake cable on your Ford F150, it’s an easy job that any car owner can do. All you’ll need is a few basic tools and some replacement parts. The most important part of the process is making sure that all connections are tight and secure before driving away again.

The entire process should take just a few hours, so if you’re looking for a quick repair project this weekend, replacing your Ford F150’s parking brake cable could be the perfect solution!

How to Replace Rear Driver's Side Parking Brake Cable 1997-2003 Ford F-150

What are the Symptoms of a Bad Parking Brake Cable?

If you notice that your parking brake is not functioning correctly, it may be a sign of a bad parking brake cable. The most common symptom of an issue with your parking brake cable is when the lever does not stay in place when engaged. This can be caused by worn or frayed cables, or even corrosion if the car has been exposed to moisture for long periods of time.

Additionally, if the pedal feels loose or spongy when depressed, this could also indicate a problem with the cable. If you hear grinding sounds coming from either wheel area while engaging and disengaging the parking brake then there might be an obstruction on one end of the cable which will need to be cleared away before normal function can resume. It’s important to address any issues with your parking brakes as soon as possible since they are responsible for holding your vehicle stationary and preventing it from rolling unexpectedly during parked situations.

How Do You Reset the Parking Brake on a Ford F150?

Resetting the parking brake on a Ford F150 is an easy process that can be completed in just a few steps. First, make sure that you have the right tools to do the job. You’ll need a wrench and some pliers.

Then, open your hood and locate the parking brake lever on the driver’s side of your vehicle. Once you have located it, use your wrench to loosen its adjustment nut until it’s completely loose. Now use your pliers to turn both of the locking bolts clockwise until they are secure but not too tight or they may break off during operation.

Finally, press down firmly on the release pedal while making sure that all four wheels are still touching flat ground in order for this step to be successful. With these steps complete you should now have successfully reset your F150’s parking brake!

Can You Drive Without a Parking Brake Cable?

The answer to this question is no, you cannot drive without a parking brake cable. A parking brake cable is an important part of any vehicle’s braking system as it serves to keep the car from moving when parked in place. This cable helps prevent the car from rolling away which can be very dangerous if not properly secured with a functioning parking brake.

Without the use of a parking brake cable, your vehicle could move unexpectedly even after coming to a complete stop and result in serious injury or even death. Therefore, it’s always best practice to ensure that your parking brake cables are working correctly before getting behind the wheel of your car. Not only will this protect you and others around you while driving but also help maintain proper operation of all components connected with your braking system for optimal safety on the road ahead!

How Hard is It to Replace a Handbrake Cable?

Replacing a handbrake cable is no easy task. It requires time, knowledge and the right tools for the job. Generally speaking, it can take anywhere from two to four hours depending on the make and model of your vehicle and how difficult it may be to access certain components of your handbrake system.

To begin with, you’ll need to locate all three handbrake cables that run between the mechanism in your car’s center console and each rear wheel hub assembly. You’ll then have to determine which one needs replacing before disconnecting it from its hubs at both ends. After this has been completed, you’ll need to remove any existing parts such as springs or clips that secure the old cable in place before installing a new replacement cable back into position.

Once everything is securely fastened in place, you should check for proper operation by testing out several short stops with your brakes applied just enough so that they engage properly without locking up or producing too high an amount of resistance when released again. If all goes well, congratulations! You’ve successfully replaced your own handbrake cable!

Ford F150 Parking Brake Cable Replacement


Ford F150 Parking Brake Diagram

The Ford F150 parking brake diagram is a helpful visual aid that outlines the inner workings of this complex system. It helps drivers understand how to properly operate the parking brake, as well as showing them where all the components are located and how they interact with each other. A detailed understanding of this component can help ensure your vehicle remains safe when parked on slopes or uneven surfaces.

2013 F150 Parking Brake Cable Replacement

If you’re looking to replace the parking brake cable on your 2013 F150, it’s important to keep in mind that this job is best left for professional mechanics. The process of replacing a parking brake cable can be tricky and requires specialized tools and knowledge in order to ensure that all components are properly installed, adjusted and functioning correctly. If done incorrectly, the brakes may not function properly or could even fail completely – something no driver wants to experience!

How to Remove Parking Brake Cable from Drum

Removing the parking brake cable from a drum is a relatively straightforward process that almost anyone can do with some simple tools. To begin, you’ll need to locate the two mounting brackets on either side of the parking brake cable and remove them using an adjustable wrench or a socket set. Following that, you should be able to pull out the cable itself and disconnect it from its housing.

Once this is done, your parking brake will be ready for installation of a new one!


Replacing the parking brake cable on a Ford F150 is not a difficult job and can be done with basic tools. The process should take no more than an hour or two, depending on your experience level. With the right preparation and proper instructions, you can successfully replace this part in your vehicle without getting any help from a professional mechanic.

It’s important to always check that all parts are properly connected before driving away to ensure safety while operating the vehicle.


  • Zayn

    John Zayn Smith is a renowned truck enthusiast, automotive industry expert, and author. Beginning his career as a mechanic, Zayn's curiosity led him to explore all facets of the trucking world, sharing his insights through in-depth articles on His knowledge spans truck mechanics, trends, and aftermarket modifications, making him a trusted resource for both professionals and hobbyists. Outside writing and mechanics, Zayn enjoys off-roading, truck shows, and family time. Follow his work for the latest in truck-related news and tips.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *