Jeep Gladiator Oil Life Reset Using the Cluster or Pedal Method
To reset the oil life on a Jeep Gladiator, turn the ignition to ON/RUN without pressing the brake or starting the engine, open Oil Life under Vehicle Info in the instrument cluster display, then press and hold OK until the gauge reads 100%.
Jeep prints the same steps in its 2020, 2021 and 2023 Gladiator owner’s manuals, along with a backup method that uses the accelerator pedal. Both work from the driver’s seat with no tools.
This Jeep Gladiator oil life reset guide covers both methods, what the Oil Change Required message means, the service limits Jeep sets and the oil to use before you reset.
How to Reset Gladiator Oil Life in 3 Cluster Steps
The instrument cluster method is the primary procedure in the Oil Life Reset section of Jeep’s 2023 Jeep Gladiator owner’s manual. Do it after the oil and filter are changed, not before.
- Set the ignition to ON/RUN. Keep your foot off the brake pedal so the truck does not start. The dash lights up, but the engine stays off.
- Open the Oil Life screen. Use the up and down arrow buttons for the cluster display to reach Vehicle Info, then the left and right arrow buttons to scroll to the Oil Life submenu.
- Hold OK. Press and hold the OK button until the oil life gauge returns to 100%.

The process is quick once you know the menu. If the gauge shows 100%, the reset is complete and you can start the truck normally.
The Gladiator Accelerator Pedal Reset in 3 Steps
Jeep’s manuals also list a secondary method that needs no menu at all. We suggest it as a backup if the menu reset does not take.
- Set the ignition to ON/RUN without the brake. As before, the engine must not start.
- Press the accelerator three times. Fully press the pedal slowly three times within ten seconds.
- Turn the ignition to OFF. Keep your foot off the brake pedal while you switch it off.
Start the truck afterward to confirm the result. If the Oil Change Required message appears again, the manual says the system did not reset, so repeat the procedure.
Timing matters with this method. The manual specifies slow, full presses inside the ten-second window, so quick or partial taps may not register.
4 Cluster Button Functions Used in the Gladiator Reset
The cluster method depends on four button functions that Jeep describes in the instrument cluster display section of the manual.
| Control | What it does in the reset |
|---|---|
| Up and down arrows | Cycle through main menu items until Vehicle Info appears |
| Left and right arrows | Scroll through the Vehicle Info submenus to Oil Life |
| OK, short press | Selects a screen and temporarily clears the oil change message |
| OK, held | Resets the selected item, such as oil life, back to 100% |
Vehicle Info holds more than oil life. The 2023 manual lists tire pressure, coolant temperature, transmission temperature, oil pressure, oil temperature, oil life and battery voltage, plus diesel exhaust fluid level on equipped trucks.
Holding OK on the wrong submenu does not reset oil life. Confirm the screen reads Oil Life before you press and hold.
The manual says holding OK for about two seconds resets whatever feature is displayed or selected. That is why the Oil Life screen must be showing before you hold the button, and why the gauge reading is the confirmation to watch.
What the Gladiator Oil Change Required Message Means in 4 Points
The reset exists to clear one message. Here is how Jeep’s manual says it behaves.
- It signals the next scheduled oil change. The message appears for five seconds after a single chime.
- It comes back at every start. Until you reset the system, it returns each time the ignition goes to ON/RUN.
- A short OK press only hides it. Pressing and releasing OK clears it for that drive, but it returns next time.
- Service is due soon. Jeep says to have the oil changed within the next 500 miles after the message appears.
An authorized dealer resets the message as part of an oil change. If someone else does the work, you need to run the reset yourself, or the message will keep returning at every start.
Gladiator Oil Change Limits for the 3.6L and 3.0L Engines
Jeep’s manual says the oil change indicator is based on engine operating conditions, so the interval changes with how you drive. Short trips, towing and extreme temperatures can bring the message on sooner.
The monitor never overrides Jeep’s outer limits. For the 3.6L V6, the 2023 manual says oil changes should never exceed 10,000 miles, 12 months or 350 hours of engine run time, whichever comes first.
For the 3.0L EcoDiesel, the limit is 10,000 miles or 12 months. In states that require biodiesel blends above 5 percent, the manual calls for oil and fuel filter changes every 8,000 miles and at least every 6 months.
The 350-hour limit mostly affects trucks that idle for long periods, which the manual notes is a fleet concern. Trailer towing is another heavy use, so check our Jeep Gladiator tow capacity chart if you pull regularly.
When to Reset Gladiator Oil Life in 3 Situations
The reset tells the monitor that fresh oil went in. Running it at the wrong time hides a real service need, so match the action to the situation.
After a DIY Oil Change
Reset right after the new oil and filter are in and the level checks out. The monitor then counts down from 100% on fresh oil.
After a Dealer Oil Change
Jeep’s manual says an authorized dealer resets the indicator after the service. Start the truck before you leave to confirm the message is gone.
After a Top Off Only
Adding a quart does not replace worn oil, so do not reset the monitor. Leave it counting until the full oil and filter change is done.
How to Check Gladiator Oil Level in 4 Steps Before the Reset
A reset after a short fill or an overfill sets the clock on oil that is already a problem. The 2023 manual’s oil level check works like this.
- Park on level ground. A tilted truck gives a false dipstick reading.
- Warm up, then wait five minutes. Check about five minutes after shutting off a fully warmed engine so oil drains back to the pan.
- Read the crosshatch. Keep the level inside the crosshatch area on the dipstick, whatever marking style your dipstick uses.
- Add oil in small amounts. The manual says one quart moves the level from the low end to the high end of the crosshatch.
Do not overfill. Jeep warns that too much or too little oil can cause aeration or loss of oil pressure, which can damage the engine.
Jeep also advises against oil additives other than leak detection dyes and says chemical engine flushes can cause damage that the warranty does not cover. On the diesel, each oil change also includes filling the Diesel Exhaust Fluid tank and servicing the fuel filter, and a DEF Service Required warning needs its own attention.
3.6L and 3.0L Gladiator Oil Specs to Use Before Resetting
A reset only makes sense if the new oil matches Jeep’s specification. The 2023 manual lists different oil for each engine.Engine Oil with filter Viscosity Material standard 3.6L Pentastar V6 gas 5.0 qt (4.7 L) SAE 0W-20 full synthetic MS-6395 3.0L EcoDiesel V6 9.0 qt (8.5 L) SAE 5W-40 full synthetic MS-12991 
Jeep says an equivalent 0W-20 oil must carry the API Starburst mark. For the diesel, an equivalent oil must meet API SN or SP and ACEA A3/B4.
The manual also asks for a filter that meets SAE/USCAR-36 if a Mopar filter is not available. For brand-level choices, see our guide to the best oil for the Jeep Gladiator.
Why a Gladiator Oil Life Reset Fails in 4 Common Cases
Most failed resets come from small setup mistakes. Check these before you repeat the steps.
Brake Pedal Pressed
Both methods require the brake pedal to stay released, according to Jeep’s manual. If the engine starts, switch it off and begin again.
Engine Already Running
Jeep’s steps say not to start the engine. Turn the truck off, then return to ON/RUN with your foot off the brake.
OK Released Too Early
The gauge has to reach 100% before you let go. A short press only hides the message for one drive.
Pedal Presses Too Fast
The pedal method needs three slow, full presses inside ten seconds. Partial or rushed presses can miss the window.
Gladiator Model Years Covered by the 2020 to 2023 Manuals
The Gladiator has used the same reset logic since launch, but the engine lineup changed. These are the points worth knowing by year.
- 2020 to 2023. Jeep’s 2020, 2021 and 2023 owner’s manuals print both reset methods with the same steps. The 2021 Gladiator owner’s manual places them on page 100.
- 2021 to 2023 EcoDiesel. The 3.0L diesel uses the same reset, but different oil and capacity. The Detroit Bureau reported that the 2023 Rubicon FarOut marked the final EcoDiesel Gladiator.
- 2024 to 2026. We could not confirm these manuals, so check the Oil Life Reset entry in yours before you start. For 2026, Jeep’s What’s New for 2026 Gladiator release lists only the 3.6L V6 with an eight-speed automatic.
- 2027. Autoevolution reports the 2027 Gladiator keeps the 285 hp 3.6L V6 and a seven-inch color cluster on the Sport S, now the entry trim.
Jeep posts Gladiator owner’s manuals on its vehicleinfo.mopar.com site. Search the index for Oil Life Reset if your truck’s menu labels look different.
Jeep Gladiator Oil Life Reset Checklist
5 checks- 1Change oil first. Use 0W-20 MS-6395 for the 3.6L or 5W-40 MS-12991 for the 3.0L diesel.
- 2Ignition to ON/RUN. Brake pedal released, engine not started.
- 3Open Vehicle Info. Scroll to the Oil Life submenu with the arrow buttons.
- 4Hold OK. Keep holding until the gauge reads 100%.
- 5Start and confirm. No Oil Change Required message means the reset worked.
Source: Jeep Gladiator owner's manuals, 2020, 2021 and 2023 editions. Backup method: three slow full accelerator presses within ten seconds.
The checklist above condenses the whole job, from the oil change to the confirmation start, into five checks.
Getting the Jeep Gladiator Oil Life Reset Right the First Time
A Jeep Gladiator oil life reset takes one menu path: ignition to ON/RUN without the brake, Vehicle Info, Oil Life, then hold OK until 100%. If that fails, the three-press accelerator method is the backup.
Reset only after the correct oil goes in, which is 0W-20 for the 3.6L and 5W-40 for the 3.0L EcoDiesel, and after the dipstick reads inside the crosshatch. Skip the reset entirely if you only topped off the oil.
Then start the truck and watch for the message. No message means the monitor is counting from 100% again, and your next service will arrive on the schedule Jeep intended.
Jeep Gladiator Oil Life Reset FAQ in 6 Answers
How Do I Reset Gladiator Oil Life?
Turn the ignition to ON/RUN without pressing the brake, open Vehicle Info, scroll to Oil Life and hold OK until it reads 100%. Jeep prints this as the primary method in its Gladiator owner’s manuals, and the backup uses three slow accelerator presses within ten seconds.
Can I Reset It Without the Menu?
Yes. With the ignition in ON/RUN and the brake released, press the accelerator fully and slowly three times within ten seconds. Then turn the ignition to OFF without touching the brake and start the truck to confirm. If the message returns, the manual says to repeat the steps.
Why Does the Oil Message Return?
The monitor was not reset, or the reset did not take. A short OK press only hides the message for one drive, so hold OK on the Oil Life screen until 100% or repeat the pedal method. Jeep wants the oil changed within 500 miles of the message.
How Often Does a Gladiator Need Oil?
Follow the oil life monitor, but never exceed 10,000 miles or 12 months, according to Jeep. The 3.6L also has a 350-hour engine run time limit, and service is due within 500 miles of the message. Diesels on biodiesel blends above 5 percent need oil every 8,000 miles or 6 months.
What Oil Does the 3.6L Gladiator Use?
The 2023 manual calls for SAE 0W-20 full synthetic oil meeting MS-6395, with 5.0 quarts including the filter. An equivalent oil must carry the API Starburst mark. Our 3.6 Pentastar oil type guide covers the same engine in other trucks.
Does a Dealer Reset the Oil Life?
Yes. Jeep’s manual says an authorized dealer resets the oil change message after servicing the truck. If you or an independent shop change the oil, run the reset yourself before the next drive, or the message will return at every start.





























![How To Program A Dodge Key Fob [2026]](https://truckguider.com/wp-content/uploads/2026/03/featured-45ae9f7f-768x403.webp)




![How to Reset Service Trailer Brake System: Step-by-Step Guide [2026]](https://truckguider.com/wp-content/uploads/2026/03/how-to-reset-service-trailer-brake-syste-featured.webp)