To reset the tire location on a vehicle after a tire rotation, an OBD2 scanner tool is required. This type of diagnostic tool connects to the car’s onboard diagnostics port and is used to communicate with the computer system inside the car. It can read codes, clear codes, and allow you to view data from various sensors within your engine.

Some OBD2 scanners also have additional features like resetting oil service lights or resetting Tire Pressure Monitoring System (TPMS) sensors after tire rotations. The steps for this vary depending on which scanner you are using but typically involve selecting ‘Reset TPMS Sensor’ from within the menu options, followed by entering in information about each wheel such as its size, circumference and weight before confirming that it has been correctly identified and then resetting it accordingly.

After a tire rotation, the tire location on a vehicle needs to be reset in order to ensure proper tracking and alignment. The tool used to do this is called an OBD2 scan tool. This device connects to your car’s onboard diagnostic (OBD) computer system and allows technicians to access data about the engine, transmission, brakes, suspension and other systems.

By using an OBD2 scan tool, technicians can see where each wheel should be located after the tire rotation has been completed so that they can properly adjust the wheel angles for optimal performance.

How to relearn the TPMS tire location after tire rotation 2018 Chevrolet Traverse or 2017 GMC Acadia

How Do You Reset Tire Pressure Sensor After Rotation?

Resetting the tire pressure sensor after a rotation is an important part of ensuring that your vehicle has accurate readings on its tire pressure. It’s not difficult to do, but it does require you to have some knowledge about how the system works. First, you’ll need to find out which tires were rotated and mark them with chalk or a piece of tape.

This will help make sure that when you reset the sensors, they are in their correct positions. Next, use a tire pressure gauge to check each tire’s air pressure and make sure it is at the recommended level for your vehicle (which can usually be found in your owner’s manual). Once all four tires are properly inflated, use an OBD-II tool (or Onboard Diagnostics) connected to your car’s computer system in order to reset the TPMS using specific codes from your car manufacturer’s website.

After successfully completing these steps, start up your engine and drive around for approximately 20 minutes so that all four tires register on the TPMS again before turning off the engine and confirming that everything was done correctly. Resetting a tire pressure sensor after a rotation may seem like a daunting task but following these simple steps should help ensure accuracy and safety while driving!

How Do You Reset a Tire Location?

Resetting a tire location can be done relatively easily with the right tools and knowledge. First, you’ll need to jack up the vehicle so that you can access all four of its tires. Once lifted, take off each wheel using lug nuts or other fasteners until all four wheels are removed from the car.

When this is done, resetting your tire locations requires putting them back in their original positions. To do this accurately and safely, it’s important to use a torque wrench to properly tighten each nut or bolt on the wheels after they have been re-positioned on the car. Additionally, if you don’t feel comfortable doing this yourself or are not sure what size wrench is needed for your particular model of vehicle then it’s best to get help from an experienced automotive technician who will know exactly how much tension should be applied during installation.

Doing these steps correctly will ensure that your tires remain securely mounted and that your car remains safe while driving down roads and highways alike!

What is a Relearn Tool for Tires?

A tire relearn tool is an essential piece of equipment used in the automotive industry to reset a vehicle’s tire sensors after changing, rotating or balancing tires. It is important that the sensors are correctly programmed so they can send accurate information back to the vehicle’s computer system, which then helps it calculate fuel efficiency and performance metrics. Tire relearn tools allow you to quickly reset your tire sensors with just a few steps, saving mechanics time and effort when replacing or servicing tires.

Additionally, this tool eliminates guesswork as it ensures that all four tires are properly balanced with no variance from one side of the car to another. This improves overall ride quality and provides greater control over how your car handles on different surfaces.

Do I Need a Tpms Relearn Tool?

When it comes to getting the most out of your tire pressure monitoring system (TPMS), one tool you should consider investing in is a TPMS relearn tool. A TPMS relearn tool allows you to calibrate your tire sensors so that they can accurately detect and report changes in the air pressure of your tires. This is important because if any of the tires on your vehicle are underinflated, it could lead to poor handling, decreased fuel efficiency, and even premature wear on other components such as brakes or suspension parts.

With a TPMS relearn tool, you can quickly diagnose any issues with the sensor readings and ensure that all four of your tires remain properly inflated at all times. Not only will this help keep you safe while driving but it will also save you money by avoiding unnecessary repairs due to premature wear caused by an improperly inflated tire. Investing in a TPMS relearn tool is an easy way to get the most out of your car’s tire pressure monitoring system and ensure that all four tires remain properly inflated at all times – ultimately keeping both yourself and others safe while driving!

What Tool is Used to Reset the Tire Location on a Vehicle After a Tire Rotation?


How to Reset Tire Sensors After Rotation

Tire sensors are designed to monitor the air pressure in your tires and alert you when it’s time to add more air. However, after rotating your tires, you may need to reset the tire sensors so that they can continue to accurately measure and report on your tire pressure. To do this, simply use a Tire Pressure Monitoring System (TPMS) relearn tool or refer to your vehicle owner’s manual for specific instructions.

Once complete, make sure all of the tire pressures are properly balanced before driving away!

Do You Need to Reset Tpms After Tire Rotation

Yes, it is important to reset your Tire Pressure Monitoring System (TPMS) after a tire rotation. This ensures that each of the four tires will be accurately monitored for pressure levels and prevent any issues from occurring due to incorrect readings or lack thereof. It’s best to take your car into an auto shop if you are uncomfortable performing this task yourself, as the TPMS needs to be calibrated in order for it work properly.

What Can Happen If Tpms Systems are Not Reset After Tire Rotation?

If TPMS systems are not reset after a tire rotation, the system will continue to display incorrect tire pressure readings for each of the tires. This could lead to an inaccurate understanding of how much air is in each tire and can cause unsafe driving conditions. Additionally, if the TPMS sensors are not properly calibrated after a tire rotation, it may result in false alarms being triggered when no problems actually exist.


From this blog post, it is clear that a tire reset tool is the go-to choice for resetting the tire location on a vehicle after a tire rotation. This tool can be used to reprogram the ECU and help restore proper functionality of the car’s monitoring systems. It is easy to use and cost-effective, making it an ideal solution for any vehicle owner seeking to reset their tires location after a rotation.

With its versatility and convenience, this tool can provide peace of mind as well as ensure your safety by helping you maintain accurate data in regards to your car’s tire locations.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *