2013 Ram 1500 Driver Side Blend Door Actuator Location
If you’re looking for the blend door actuator on your 2013 Ram 1500, you’ll find it on the driver’s side of the dash. It’s a small, black box that controls the airflow from the vents. The actuator is located behind the glove box and is held in place by two screws.
If you’re having trouble with your 2013 Ram 1500’s driver-side blend door actuator, you’re not alone. Many Ram owners have reported this issue and it can be a real pain to deal with. Luckily, we’ve got a handy guide that will show you exactly where the actuator is located and how to replace it.
So if you’re ready to get your hands dirty, read on! The first thing you’ll need to do is remove the glove box. There are two screws that hold it in place, so simply remove those and set the glove box aside.
Once the glove box is out of the way, you’ll see the actuator mounted on the HVAC housing. There are three screws holding it in place, so remove those and carefully pull the actuator out. Now all that’s left to do is install the new actuator in reverse order and you should be good to go!
2013 Dodge Ram 1500 blend door acturator replacement
Where is the Blend Air Door Actuator Located?
The blend air door actuator is located on the left side of the dash, just behind the glove box. It is a black plastic piece that is about 2 inches wide and 4 inches long. There are two screws that hold it in place, and there are two wires running to it.
One wire is for the power and the other is for the ground.
How Do You Change the Blend Door Actuator on a Dodge Ram?
If you’re having trouble with your Dodge Ram’s blend door actuator, there are a few things you can do to try and fix it. First, check the fuse box to make sure that the fuse for the blend door actuator is not blown. If it is, replace it and see if that fixes the problem.
If not, then you’ll need to remove the glove box and access the actuator from there. It’s a good idea to disconnect the battery before doing any work on electrical components in your vehicle. Once you have access to the actuator, you can try manually moving the door to see if it’s just stuck.
If it is, then gently pry it loose and move it back into place. If the door seems to be working properly but the air isn’t flowing correctly, then chances are there’s an issue with the vacuum lines. Check all of the lines going to and from the actuator and make sure they’re all connected and not blocked or leaking.
Are There Two Blend Door Actuators?
Most cars have two separate blend door actuators, one for the hot side and one for the cold side. The actuator controls a small flap inside the HVAC system that directs airflow through the heater core or around it. If your car only has one actuator, it’s probably controlling both doors.
How Do I Reset My Blend Door Actuator?
If your car’s air conditioning system is only blowing hot air, the problem could be with the blend door actuator. This part controls the flow of coolant to the heater core, and if it’s not working properly, it can cause your AC system to malfunction. Luckily, resetting the actuator is a relatively easy process that you can do at home.
To reset your blend door actuator: 1. Start by disconnecting the battery. This will ensure that there is no power going to the actuator while you’re working on it.
2. Next, locate the actuator. It should be located near the heater core, behind the glove box or under the dash. 3. Once you’ve found it, disconnect the electrical connector from the actuator.
You may need a screwdriver to help with this step. 4. With the connector disconnected, use a pair of pliers to manually move the door back and forth until you feel it click into place. Be careful not to force it too much – you don’t want to damage anything!
5. Reconnect the battery and turn on your car’s ignition (but don’t start the engine). The light on your dashboard should come on – if it doesn’t, repeat steps 1-4 until it does come on.
2013 Dodge Ram 1500 Blend Door Actuator Diagram
If you’re having trouble with your 2013 Dodge Ram 1500’s blend door actuator, you’re not alone. Many owners of this truck have had the same issue. The good news is that there is a fix for it, and it’s relatively easy to do yourself.
The first thing you’ll need to do is locate the actuator. It’s located on the passenger side of the dash, behind the glove box. Once you’ve found it, disconnect the electrical connector and remove the two screws that hold it in place.
Next, you’ll need to remove the old actuator motor. To do this, simply pull it out of its housing. Be careful not to damage the housing itself, as you’ll need to reuse it later.
Now, take your new actuator motor and insert it into the housing. Make sure that it’s seated properly and reconnect the electrical connector. Finally, replace the two screws that hold everything in place.
2013 Ram 1500 Blend Door Location
If you’re looking for the 2013 Ram 1500 blend door location, it’s actually pretty easy to find. Just look in the engine compartment on the driver’s side. The blend door is located behind the engine air filter housing.
2013 Ram 2500 Blend Door Actuator Location
Assuming you are talking about the Blend Door Actuator for the HVAC system:
The blend door actuator is located on the passenger side of the dash, above the glove box. It is a motor that controls the position of the blend door, which mixes hot and cold air from the HVAC system.
If your 2013 Ram 2500 has no heat or only blows cold air, then it is likely that the blend door actuator has failed.
If you’re having trouble with your 2013 Ram 1500’s driver-side blend door actuator, this post will show you where to find it. The actuator is located behind the glove box and can be accessed by removing the kick panel and unscrewing the two screws that hold it in place. Once you have access to the actuator, simply unplug it from the electrical connector and remove it from the vehicle.