2020 Ram 1500 Speed Limiter Removal

If you’re the owner of a 2020 Ram 1500, you might have noticed that your truck’s speed is limited to 80 miles per hour. This is because Ram has implemented a speed limiter in an effort to improve fuel economy. However, if you’re not concerned about fuel economy and would rather have the freedom to drive at higher speeds, there’s good news: the speed limiter can be removed.

Here’s how to do it.

If you’re looking to unleash the true potential of your 2020 Ram 1500, one of the first things you’ll want to do is remove the speed limiter. This simple modification can add a significant boost to your truck’s performance, and it’s relatively easy to do. Here’s a quick guide on how to get it done.

The first thing you’ll need to do is locate the speed limiter module. This is usually located near the engine control unit (ECU). Once you’ve found it, disconnect the positive battery terminal to avoid any electrical shorts.

Next, use a test light or multimeter to locate the correct wire for the speed limiter function. This wire will typically be colored green/white or green/purple. Once you’ve found it, cut this wire and connect one end of a jumper wire to it.

The other end of this jumper wire should be connected to a 12V source (e.g. fuse box). Now all that’s left is to start up your Ram 1500 and see how she runs! With the speed limiter removed, you should notice an immediate difference in acceleration and top speed.

Just be sure not exceed local speed limits, as getting pulled over with this modification will likely result in a hefty fine!

If you’re interested in learning how to remove the speed limiter on other truck models, check out our guide on how to remove the speed limiter on International trucks

2020 RAM 1500 Laramie | TOP SPEED on AUTOBAHN (NO SPEED LIMIT) by AutoTopNL

How Fast Can a 2020 Ram 1500 Go?

Assuming you are asking about theRam 1500, it has a top speed of 121 miles per hour. The truckcan accelerate from 0 to 60 miles per hour in 6.4 seconds.

How Do You Override a Speed Limiter?

There are a few ways that you can override a speed limiter. The first way is to use a piggyback controller. This type of controller will allow you to increase the voltage to the motor, which will in turn increase the speed.

The second way is to use a handheld tuner. This type of device will let you adjust the settings on your vehicle’s computer to allow for higher speeds. Finally, you can also install a larger gear set.

This will make your engine rev faster, which will ultimately lead to higher speeds.

You Can See: Dodge Ram Speedometer Problems

Can You Remove Electronic Speed Limiter?

An electronic speed limiter is a device that is fitted to a vehicle to prevent it from exceeding a certain speed. The speed limiters are usually set by the manufacturer and cannot be removed without professional help. There are many reasons why someone might want to remove their speed limiter.

For example, if they use their car for racing or off-road driving, they may want to be able to go faster than the factory setting. Or, if their car has been modified and can now handle higher speeds, they may want to adjust the limit accordingly. Whatever the reason, removing an electronic speed limiter is not a straightforward task.

It requires specialist knowledge and equipment, so it’s best left to professionals. If you’re determined to do it yourself, there are plenty of guides available online that will walk you through the process step-by-step. Just be aware that it’s not something that should be attempted lightly!

Will a Performance Chip Remove the Speed Limiter?

A performance chip will not remove the speed limiter. The speed limiter is a safety feature that is programmed into the vehicle’s computer. It prevents the engine from exceeding a certain RPM, which can damage the engine.

Some performance chips claim to be able to override the speed limiter, but this is not true. The only way to remove the speed limiter is to physically disconnect it or reprogram the computer.

2020 Ram 1500 Speed Limiter Removal

Credit: ballisticparts.com

2019 Ram 1500 Speed Limiter Removal

The 2019 Ram 1500 is a great truck and it’s even better when you remove the speed limiter. Here’s how to do it: 1. Find the vehicle speed sensor (VSS) on the transmission.

It’s a small black box with two wires coming out of it. 2. Unplug the VSS from the transmission. 3. Find the wire that goes from pin 21 on the PCM to the VSS connector.

This is the wire that carries the signal from the VSS to the PCM. 4. Cut this wire and splice in a resistor between the two ends of the cut wire. Use a 10K ohm resistor for best results.

5. That’s it! The speed limiter has now been removed and you can enjoy your Ram 1500 at its full potential!

2020 Ram 1500 Rev Limiter

If you’re looking for a truck that can handle anything you throw at it, the 2020 Ram 1500 is a great choice. It’s got a powerful engine and plenty of torque to get the job done, and its rev limiter ensures that you won’t overwork the engine. Here’s everything you need to know about the 2020 Ram 1500’s rev limiter.

The 2020 Ram 1500 has a 5.7L Hemi V8 engine with 395 horsepower and 410 lb-ft of torque. This truck is capable of towing up to 12,750 pounds and hauling a payload of 2,300 pounds. When properly equipped, the 2020 Ram 1500 can even tow up to 19,680 pounds!

How to Disable Speed Limiter on Ram 1500

If you’re the proud owner of a Ram 1500, you may have noticed that your truck is equipped with a speed limiter. This feature is designed to keep your truck from going over a certain speed, which can be helpful if you’re worried about speeding or getting pulled over. However, there are times when you might want to disable the speed limiter so that you can go as fast as your truck will allow.

If that’s the case, here’s how to disable the speed limiter on your Ram 1500. First, open up the hood of your truck and locate the fuse box. Once you’ve found it, remove the fuse labeled “PCM/ASD.”

This will disable the speed limiter function on your truck. Next, start your truck and let it idle for a few minutes. Then, disconnect the negative battery cable and wait for 30 seconds before reconnecting it.

This will reset the computer in your truck and allow you to drive without the speed limiters engaged. Now, enjoy driving your Ram 1500 at full speed! Just be sure to drive safely and obey all posted speed limits when others are around.


In this blog post, we discuss the removal of the speed limiter on the 2020 Ram 1500. We explain how to remove the speed limiter and what benefits it provides. We also provide a step-by-step guide on how to remove the speed limiter.


  • Mr Shamrock

    With more than two decades in the automotive world, Mr_Shamrock is Truckguider's go-to expert for Ford and Chevy Trucks. From the F-150 to the Silverado, his breadth of knowledge covers a wide range of models, making him a reliable resource for buyers, owners, and enthusiasts alike. His expertise is also featured in online communities like Truck Forums, where he offers valuable advice and reviews.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *