6.4 Hemi Oil Filter Location

The oil filter on a 6.4 liter Hemi engine is located on the lower side of the engine block, near the front passenger wheel well. It sits just above where the transmission meets with the block and can be accessed by removing two bolts that secure it in place. The filter itself is an oval shape, about 4 inches long and 2 inches wide.

Be sure to use a wrench or socket to loosen it from its mounting bracket before attempting to remove it. Additionally, you will need an oil filter wrench or pliers in order to unscrew it from its housing as regular wrenches won’t fit around its circumference due to its size and shape. Once removed, replace with a new filter and re-secure back into place using your tools of choice.

If you own a vehicle with a 6.4 Hemi engine, you will need to know where the oil filter is located in order to keep it running smoothly and efficiently. The oil filter on the 6.4 Hemi is located on the passenger side of the engine block, just underneath the intake manifold. It’s important to make sure that your oil filter is regularly changed as part of regular maintenance; this helps prevent dirt and debris from clogging up your engine and causing damage over time.

Changing your oil filter can also help ensure that your engine runs at its best performance level for years to come!

6.4L hemi oil change tip

Where is the Oil Filter Located on a Ram 2500?

The oil filter on a Ram 2500 is located in the engine bay, and can be found between the firewall and the driver’s side wheel well. It is typically mounted to the block of your engine using two bolts or screws, though some models may have only one fastener. To access it, you’ll need to locate the oil pan and drain plug which are both nearby.

Once you’ve located these components, take off their covers (if applicable) and then remove any other obstructions such as hoses or wires that might be in the way before attempting to remove your filter. Be sure to use a wrench when loosening any bolts or screws so that you don’t damage them during removal. After draining all of your old oil from the Ram 2500’s oil pan, replace its old filter with a new one of similar size before refilling it with fresh motor oil according to manufacturer specifications.

Where is the Engine Oil Filter Located?

The engine oil filter is an essential component of your vehicle’s maintenance system. It is designed to filter out dirt and debris from the motor oil, thus helping keep your engine running smoothly. The location of the engine oil filter depends on the type and model of your car or truck.

On most vehicles, it will be located in a housing near the bottom-front side of the engine block and can usually be accessed by removing a few bolts or screws. Additionally, some cars may have their filters located beneath other components such as alternators or air intake systems – so if you are unsure where to look, consult with your owner’s manual for further instructions. Once you know where it is located, use a wrench to unscrew the old filter before replacing it with new one that meets your specific make and model requirements.

Be sure to also check for any loose connections between the filter housing unit and its corresponding hoses during this process; otherwise they could loosen over time leading to potential leaks down the road!

How Many Quarts of Oil Does a 6.4 Ram Take?

A 6.4 Ram typically takes between 7-9 quarts of oil, depending on the model year and engine type. It is important to check your owner’s manual for exact specifications, as this can vary by make and model. When changing the oil in a 6.4 Ram, it is essential to use a high-quality synthetic motor oil that meets or exceeds the manufacturer’s specifications for viscosity, detergent levels, antiwear additives and other performance standards.

Additionally, you should also always replace the filter when changing the oil in order to ensure full protection from contaminants while keeping all internal components lubricated properly. Finally, be sure to dispose of used oil properly; never dump it down storm drains or sewers where it can pollute local waterways!

Where is the Oil Filter on a Dodge Ram Truck?

The oil filter on a Dodge Ram truck is located in the engine compartment, typically mounted to the lower driver’s side of the engine block. It is easily recognizable as it looks like a large cylinder with several hoses connected to it. Depending on the model year and type of your Dodge Ram, you may need an oil filter wrench or socket to reach and remove it for replacement.

If you are unsure about what tool you need, consult your owner’s manual or seek assistance from an experienced mechanic for help. After loosening and removing the old filter, make sure that all gaskets and seals have been replaced before installing the new one back into place. As with any other routine maintenance task, be sure not to overfill or underfill your vehicle with fresh oil when replacing its filter; always check your owner’s manual for specific instructions pertaining to this procedure.

6.4 Hemi Oil Filter Location

Credit: www.workplaydrive.com

6.4 Hemi Oil Capacity

The 6.4 Hemi engine holds 7 quarts of oil in the oil pan, so it’s important to make sure you use the correct amount when changing your oil. To ensure optimal performance and longevity from your engine, be sure to check your owner’s manual for specific instructions on how often to change your oil and what type of oil is recommended for the 6.4 Hemi engine.

6.4 Hemi Oil Type

Using the correct oil type for your 6.4 Hemi engine is essential in order to keep it running smoothly and efficiently. The best oil for this engine type should be 5W-20 or 0W-40 synthetic motor oil that meets the standards set by the American Petroleum Institute (API). It’s also important to use a quality filter as well, such as those made by Mopar or Wix, with at least an 8 micron filtration rating.

Regular oil changes are necessary to keep your 6.4 Hemi working optimally; check your owner’s manual for recommended intervals.

Ram 2500 6.4 Hemi Oil Filter

The Ram 2500 6.4 Hemi is equipped with an oil filter that helps to ensure the engine runs smoothly and efficiently by reducing the amount of debris in the oil system. The oil filter captures dirt and other contaminants, allowing only clean filtered oil to flow through the engine’s components. This helps reduce wear on vital parts and prolongs your vehicle’s life expectancy.

Regularly replacing your Ram 2500 6.4 Hemi’s oil filter will help keep its performance at peak level for years to come.


The oil filter location on a 6.4 Hemi engine is quite easy to locate. It is located just above the starter, next to the dipstick tube and can be easily accessed with your hand or a long screwdriver. Changing your oil filter regularly helps keep your engine running smoothly and will help extend its life-span.

Remember that you should always use the correct type of oil filter when changing yours, as it may affect performance if you don’t follow manufacturer guidelines for this task.


  • Zayn

    Zohn Zayn Smith is a seasoned automotive enthusiast with over 15 years of experience in the industry. As the Founder and Chief Editor of Truckguider, he specializes in Dodge Ram models, including the Ram 1500 and Ram 2500. His deep understanding of these trucks makes him a trusted authority on everything from performance and maintenance to towing capabilities.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *