Dodge Ram Fuel Gauge Reset

The fuel gauge on your Dodge Ram is designed to give you an accurate reading of how much fuel is in the tank. However, over time, the gauge may become inaccurate due to a build-up of sediment in the tank. If this happens, you can reset the fuel gauge by following a few simple steps.

If you own a Dodge Ram, you may have noticed that the fuel gauge doesn’t always reset to “E” after you fill up. This can be frustrating, especially if you’re not sure how much fuel is actually in the tank. Luckily, there’s an easy fix.

All you need to do is cycle the ignition key from “Off” to “On” three times within five seconds. This will reset the fuel gauge and it should now accurately reflect how much fuel is in the tank. So next time you fill up your Dodge Ram, remember this simple trick to reset the fuel gauge.

It might just save you from running out of gas unexpectedly!

Dodge Ram Fuel Gauge Reset


How Do I Reset My Dodge Fuel Gauge?

If your Dodge fuel gauge is not working properly, there are a few things you can do to reset it. First, check the fuse box to see if the fuse for the fuel gauge has blown. If it has, replace it with a new one.

Next, check the wiring harness for any loose or damaged wires. If you find any, repair or replace them as necessary. Finally, if all else fails, you may need to replace the fuel gauge itself.

How Do You Fix an Inaccurate Fuel Gauge?

If your fuel gauge is reading inaccurately, there are a few potential causes. First, check the float level in the tank. If it’s too low, it could be causing the gauge to read empty when there’s still fuel in the tank.

Second, check the wiring to make sure it’s all connected properly. Third, check the sending unit to see if it’s working correctly. If none of these things seem to be the problem, then you may need to replace the entire fuel gauge assembly.

Why is My Gas Gauge Reading Wrong?

If your gas gauge is reading wrong, it could be for a number of reasons. The most common reason is that the float in the gas tank is stuck or damaged. This causes the gauge to give an inaccurate reading.

Other possible reasons include a faulty sending unit, loose wiring, or a problem with the fuel pump. If you’re not sure what’s causing the problem, it’s best to take your car to a mechanic and have them check it out.

How Do I Calibrate My Fuel Gauge?

If your vehicle has a digital readout, the process is much simpler. All you need to do is reset the system by pressing and holding the button until it reads all zeroes. For an analog gauge, you’ll need to physically remove it from your vehicle and place it on a level surface.

Once it’s level, observe where the needle rests and compare that reading to the “empty” mark on the side of the gauge. If it’s not lined up correctly, use a small screwdriver or Allen wrench to adjust the potentiometer inside the housing until it matches up.

How to Reset Dodge Ram dashboard fuel gauge

Dodge Ram Fuel Gauge Problems

If you own a Dodge Ram, you may have experienced problems with the fuel gauge. The fuel gauge is supposed to tell you how much gasoline is in the tank, but sometimes it doesn’t work correctly. There are several reasons why this might happen.

One reason could be that the float that measures the amount of gasoline has become stuck. This can happen if there is something blocking the float from moving up and down freely. Another possibility is that the wiring to the fuel gauge has become loose or damaged.

This can cause an inaccurate reading. If your fuel gauge isn’t working correctly, it’s important to get it fixed as soon as possible. An inaccurate fuel gauge can lead to running out of gas unexpectedly, which can be very dangerous.

If you’re not sure what’s causing the problem, take your truck to a mechanic and have them check it out.

Dodge Ram Fuel Gauge Stuck on Empty

If you’re driving a Dodge Ram and your fuel gauge is stuck on empty, don’t panic! This is a common problem with these trucks, and there are a few simple things you can do to fix it. First, check the fuse box under the hood.

The fuel gauge fuses are usually located in the power distribution center. If one of these fuses is blown, it could be causing your fuel gauge to malfunction. Next, check the wiring harnesses going to the fuel sending unit and make sure they’re all connected properly.

If any of the wires are loose or damaged, that could also be causing your fuel gauge to behave erratically. Finally, if neither of those solutions fixes the problem, it’s likely that the fuel sending unit itself is faulty and will need to be replaced. Fortunately, this is a relatively easy repair that can be done at home with just a few tools.

2014 Dodge Ram 1500 Fuel Gauge Problems

If you own a 2014 Dodge Ram 1500, you may have noticed some problems with your fuel gauge. The most common problem is that the fuel gauge will read “empty” when there is still gasoline in the tank. Other times, the fuel gauge may not work at all, or it may give inaccurate readings.

These fuel gauge problems can be caused by a variety of things, including a faulty sensor, a loose wire, or even water in the gas tank. If you’re experiencing any of these issues, it’s important to take your truck to a qualified mechanic so they can diagnose and fix the problem. In the meantime, here are a few tips for dealing with fuel gauge problems:

– If your fuel gauge reads “empty” when there’s still gasoline in the tank, try resetting it by disconnecting and reconnecting the battery. – If your fuel gauge isn’t working at all, you can estimate how much gasoline is in the tank by using the odometer. For every 1 mile driven, about 0.1 gallon of gasoline is used.

So if your odometer reading is at 12000 miles, you have approximately 1200 gallons of gasoline left in the tank. – To avoid water contamination in your gas tank, don’t fill up at night or during heavy rainstorms.

Ram 1500 Fuel Sensor Fail Recall

The Ram 1500 is being recalled due to a fuel sensor issue that could lead to the engine stalling. This recall affects certain model years between 2013 and 2017. If your Ram 1500 is affected by this recall, you will need to take it to a dealer to have the fuel sensor replaced.

This recall is expected to begin on June 10, 2019.


If you own a Dodge Ram, you may have experienced an issue with the fuel gauge not working correctly. If this is the case, there is a simple fix that you can do yourself. All you need to do is reset the fuel gauge by following these steps:

1. Locate the fuse box inside your Dodge Ram and find the fuse for the fuel gauge. 2. Remove the fuse and then reinsert it after about 30 seconds. 3. Start up your Dodge Ram and see if the fuel gauge is now working correctly.

By resetting the fuel gauge in this manner, you should be able to get it working properly again without having to take it into a mechanic or dealership.


  • Zayn

    Zohn Zayn Smith is a seasoned automotive enthusiast with over 15 years of experience in the industry. As the Founder and Chief Editor of Truckguider, he specializes in Dodge Ram models, including the Ram 1500 and Ram 2500. His deep understanding of these trucks makes him a trusted authority on everything from performance and maintenance to towing capabilities.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *