Briggs And Stratton Intek Torque Specs

Briggs & Stratton Intek engines are single-cylinder OHV (overhead valve) engines that range in horsepower from 4.5 to 20 HP and come with a variety of features including electric start, manual choke and primer, dual element air cleaner and oil filter. The torque specifications for the Briggs & Stratton Intek engine vary depending on the model, but generally range between 7 to 13 ft-lbs at 2500 RPM. In addition to these base specs, each individual part may have its own specific torque requirements which must be followed when assembling or replacing parts on an Intek engine.

To ensure proper assembly of your Briggs & Stratton Intek engine it is important to refer to the appropriate service manual for detailed instructions regarding torque values for each nut or bolt type.

Briggs and Stratton Intek Torque Specs are essential for ensuring that your engine is running correctly. Knowing the correct torque specs for your specific engine can help you get the most out of your machine, as well as prevent any potential damage from improper installation or use. It’s important to properly maintain these specs in order to ensure a long-lasting, reliable performance from your Briggs and Stratton Intek engine.

Briggs & Stratton / Intek Cylinder Head Bolt Torque & Sequence

What is the Torque for Briggs And Stratton Head Bolts?

Briggs and Stratton head bolts require a certain amount of torque to make sure the engine runs properly. The specific torque required for Briggs and Stratton head bolts is 18-22 ft/lbs (24-30 Nm). To ensure that you get the correct torque, use a good quality torque wrench and follow the manufacturer’s instructions.

Make sure you tighten each bolt in an alternating pattern across each cylinder. This will help prevent warping of the cylinder heads due to uneven tightening forces on one side or another. It is also important to replace any worn or damaged mounting hardware when installing new head bolts so that they are secured properly.

Following these steps will ensure your Briggs and Stratton engine functions as intended for years to come!

What is the Torque Specs for a 22 Hp Briggs And Stratton?

The torque specs for a 22 hp Briggs and Stratton engine are as follows: The cylinder head bolts should be tightened to a torque of 40-45 Ft. Lbs., the intake manifold bolts should be torqued to 15-20 Ft.

Lbs., the connecting rod cap screws should be tightened to 25-30 Ft. Lbs.

, and the flywheel nuts should be torqued to 50-55 ft lbs . It is important that these torque specifications are followed in order for your engine components to remain securely fastened and not become loose over time. Additionally, it is recommended that you use anti seize compound on all threads when tightening any bolts or nuts on your engine, as this will help ensure proper tightening every time without worrying about galling or stripping threads due to overtightening bolt heads.

What is Torque Briggs And Stratton?

Torque Briggs and Stratton is an engine manufacturer that has been manufacturing engines since 1908. Their engines are used in a variety of applications including lawn mowers, snow blowers, generators, pressure washers, and more. The company has developed several types of engines over the years to meet different needs.

Torque refers to the amount of rotational force or twist applied when turning a shaft or other object. In terms of Briggs & Stratton’s products, their torque rating indicates how much power it can produce for its size and weight class. Higher torque ratings mean more power which is ideal for larger projects such as cutting tall grass or plowing heavy snow with a tractor-style machine.

Lower torque ratings are better suited for light tasks like trimming small areas around the house or powering smaller appliances like washing machines and air conditioners.

What Torque Should Cylinder Head Bolts Be Set At?

It is important to know the correct torque setting for cylinder head bolts, as this helps ensure an effective seal between the engine block and cylinder head. Generally speaking, most manufacturers recommend tightening these bolts to 35-40 foot-pounds of torque. However, it’s best to double check your specific vehicle’s owner manual or service manual before attempting any repairs.

Additionally, if you’re using aftermarket parts such as a performance camshaft or other bolt-on modifications that require more clamping force than stock components, you may need to increase the torque slightly (usually no more than 5 ft.-lbs.). Regardless of whether you’re dealing with stock parts or aftermarket ones, always make sure each bolt has been tightened evenly in order for them all to be at the same tension level when finished. Overtightening can lead to warping of the head deck surface which will lead to poor sealing and ultimately compromise engine efficiency and power output.

Briggs And Stratton Intek Torque Specs


Briggs And Stratton 17.5 Hp Engine Torque Specs

The Briggs and Stratton 17.5 HP engine provides a maximum torque rating of 18.4 lb-ft at 2,500 RPMs, making it an ideal choice for powering small vehicles such as mowers and generators. The engine also features a 7/8″ x 3-5/32″ crankshaft that is well suited for repair or replacement with compatible parts from other brands.

Briggs And Stratton Torque Specs Chart Pdf

The Briggs and Stratton Torque Specs Chart PDF outlines the correct torque specifications for each of the company’s engine models. This chart is a valuable tool for mechanics, as it helps ensure that bolts and other hardware components are properly tightened to prevent damage to your engine. With this document, you can always have confidence in your repairs knowing all parts are fastened correctly.

Briggs And Stratton Specs by Model Number

Briggs and Stratton is one of the leading manufacturers of small engines for outdoor power equipment. Their engines are known for their reliability, durability, and performance. By using your model number you can quickly find out the specs on any Briggs and Stratton engine including displacement, horsepower rating, and cylinder configuration.

Knowing these specs can help you make sure that any repairs or replacements parts will be compatible with your specific engine.


In conclusion, the Briggs and Stratton Intek torque specs are a valuable resource for anyone looking to maintain or repair their small engine. With information on both single-cylinder and twin-cylinder engines, as well as detailed instructions on how to properly measure torque, this blog post has provided an invaluable source of information for those who need it. Whether you’re just starting out with your engine maintenance routine or are a seasoned professional working on more complex projects, having access to reliable data like these makes any job easier.


  • Zayn

    Zohn Zayn Smith is a seasoned automotive enthusiast with over 15 years of experience in the industry. As the Founder and Chief Editor of Truckguider, he specializes in Dodge Ram models, including the Ram 1500 and Ram 2500. His deep understanding of these trucks makes him a trusted authority on everything from performance and maintenance to towing capabilities.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *