How to Reset Uconnect 12 Inch Screen

1. To reset the Uconnect 12 inch screen, press and hold down both the volume up and volume down buttons on the left side of the unit for 10 seconds. 2. After 10 seconds, a pop-up message will appear asking if you want to reboot or enter recovery mode. Select Reboot System Now with your cursor or the touchscreen.

3. The system will then shut off and restart automatically in a few moments. If it does not restart on its own, press and hold down both of those two same buttons again until it restarts itself–usually around 15-20 seconds). 4. When it restarts completely, you’ll be asked to select language preferences as well as other setup options that are required when first setting up your Uconnect 12 inch screen device such as WiFi settings etc..

Follow all prompts to complete this process successfully and enjoy using your newly reset device!

  • Step 1: Start the vehicle and press the “Phone” button located on your steering wheel
  • Step 2: Select the “Settings” option from the Uconnect menu
  • Step 3: Scroll down to “System” then select “Reset”
  • Step 4: Confirm that you would like to reset by selecting “Yes” in order to initiate the resetting process
  • Step 5: Once complete, select “Done” and exit out of all menus before restarting your Uconnect 12 inch screen display system

2019 Ram 1500 – 12” UConnect Intermittent Audio Pauses – FIXED!!

How Do I Reset My Uconnect Screen?

Resetting your Uconnect screen is easy to do, and can be done in a few simple steps. First, press the “Home” button located on the bottom of the touchscreen. Then, select “Settings” from the menu options onscreen.

Once you are in Settings, select “System Reset,” then choose “Full Reset.” This will reset all of your preferences, including all audio settings as well as any personalization or customization that has been applied to your Uconnect system. Finally, you must follow through with a restart process by pressing and holding down both buttons labeled “OK” for a few seconds until you see an image of Jeep logo appear onscreen.

After this reboot is complete, your Uconnect unit should be back to its original factory state – giving you access to all of its features once again!

How Do I Hard Reset My Uconnect System?

If you are looking to reset your Uconnect system, the process is relatively simple. First, make sure your vehicle is in park and has been running for at least 15 minutes. Then locate the 8-inch display on the center console of your vehicle.

Press and hold down both the “Tune” and “Seek” buttons simultaneously until you hear two beeps from the radio speakers indicating that a hard reset has begun. The entire process should take no longer than one minute to complete; once it’s finished, all settings will revert back to factory default and you’ll need to re-enter any personalized information such as favorite radio stations or preset destinations for navigation purposes. Afterward, restart your engine so that any changes can take effect and have fun exploring all of Uconnect’s great features!

How Do I Reset My Dodge Ram Screen?

Resetting your Dodge Ram’s screen can be a bit tricky but it is possible to do. The first step to resetting the screen is to make sure you have all of the necessary tools. You will need a Phillips screwdriver, needle-nose pliers, and possibly an 8mm socket wrench depending on your model of Dodge Ram.

Once you have gathered these tools, begin by removing any trim pieces or screws from around the edge of the instrument panel. Once those are removed, locate all four screws holding on the plastic faceplate that covers the radio and climate control modules in place. Using your Phillips screwdriver unscrew each one and carefully lift off this plate to expose both modules underneath it.

Now disconnect both cables running between them so that they can be safely removed without damaging them or their connectors. With these two components out of the way, you should now see a silver box with 4x4mm screws along its perimeter holding it in place – this is what needs to be removed for access into resetting mode for your Dodge Ram’s display unit. Use either your 8mm socket wrench or needle-nose pliers for this job before unplugging its connector at last – then press down firmly on “reset” button located near where it was plugged in until you hear a click sound confirming successful procedure completion!

How Do I Reset My Chrysler Touch Screen?

If you’re having trouble with your Chrysler’s touch screen, resetting it is a great place to start. Fortunately, the process for resetting your vehicle’s touch screen is relatively simple and straightforward. To get started, press and hold the power button on the side of the display until it turns off.

Wait about 10 seconds before powering back up by pressing and holding that same button again. After a few moments, you should see an image or logo appear onscreen indicating that the system has restarted properly. Once this happens, you may need to re-input audio settings such as radio presets or Bluetooth connections if applicable; but otherwise, all other menus should be accessible again and ready for use!

How to Reset Uconnect 12 Inch Screen


2020 Ram 12″ Uconnect Reset

If you are the proud owner of a 2020 Ram, you may be familiar with their 12″ Uconnect system. This sophisticated infotainment system is designed to make your driving experience more enjoyable and intuitive. Unfortunately, it can occasionally malfunction or need resetting. Thankfully, you can easily reset your 12″ Uconnect system by pressing and holding the power button for 10 seconds until the screen goes blank and then releasing it; this will restart the Uconnect software and should help restore functionality.

2021 Ram 12 Inch Screen Reset

The 2021 Ram 12-inch screen reset is a useful feature that allows drivers to quickly restore the factory settings of their infotainment display. This process can be completed by pressing and holding both volume buttons simultaneously for 5 seconds, which will cause the system to reboot and return all of the settings back to their original states. This makes it easy to troubleshoot any issues with your display while also allowing you to customize it as desired.

2019 Ram 12″ Uconnect Reset

The 2019 Ram 12″ Uconnect Reset is a great feature that allows you to quickly and easily reset your vehicle’s entertainment system. This reset will restore the original factory settings, allowing you to start fresh with a clean slate. It also gives you the opportunity to update any software or settings in order to keep your system running optimally.

With just a few simple steps, this easy-to-use feature can get your Uconnect up and running again in no time!


In conclusion, resetting the Uconnect 12 Inch Screen is an easy process that requires a few simple steps. By following these instructions, you can quickly restore your system to its original factory settings and get back on the road. Whether you’re experiencing trouble with your vehicle’s infotainment system or just want to start fresh, this guide will help you reset your Uconnect screen in no time!


  • Zayn

    Zohn Zayn Smith is a seasoned automotive enthusiast with over 15 years of experience in the industry. As the Founder and Chief Editor of Truckguider, he specializes in Dodge Ram models, including the Ram 1500 and Ram 2500. His deep understanding of these trucks makes him a trusted authority on everything from performance and maintenance to towing capabilities.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *